Husqvarna 4421-DXL User Manual Download Page 44 | Manualshive

Page: 44 / 68

background image

Engine Oil

NOTE:

An oil drip guard (1) can be used to prevent excess oil from dripping onto the engine base plate

(Figure 24)

.

Use an empty quart (one liter) container and cut the bottom off at an angle, then slide the open area of the
container up and under the oil filter (2) before removal. Position the port of the plastic container so oil will be
directed into the oil pan (3). A drip guard can be made by folding a piece of cardboard, thin metal, or plastic
under the oil filter, forming a channel to direct the filter port oil into the drain pan.

Dispose of used oil according to the environmental laws and regulations for your area.

26

Figure 24

Remove Engine Oil Filter

27

Figure 25

Coat Rubber Seal

4.

Use a clean rag to wipe the oil filter mounting bracket surface clean where the oil filter gasket seats.

5.

Coat filter gasket with clean engine oil

(Figure 25)

.

6.

Install the new oil filter (gas: P/N 603 00 00-06) (diesel: P/N 603 00 00-41).

See following NOTE.

NOTE:

Use only oil filters designed for your engine.

7.

Hand tighten 2/3 to 3/4 turn after the filter gasket contacts the mounting surface.

Page 42

HUV 4421 Owner’s Manual

«
...
42
43
44
45
46
...
»

Summary of Contents for 4421-DXL





































































Reviews:

No comments

Related manuals for 4421-DXL

Brand: Landoll Pages: 86

BOSS RT FATBOY 1026RT RR

Brand: Meyer Pages: 44

Brand: KAYO MOTO Pages: 11

Brand: Toro Pages: 28

Brand: Suzuki Pages: 28

Brand: Primo Water Pages: 12

Brand: OTIS Pages: 17

Brand: ABI Attachments Pages: 28

Brand: DAELIM Pages: 1

Brand: Can-Am Pages: 144

Brand: Arctic Cat Pages: 84

Brand: Tomberlin Pages: 32

Brand: Wittke Pages: 104

Brand: E-TON Pages: 35

Pendpac WITTKE RETRO FL

Brand: Labrie Pages: 130

Brand: Jayco Pages: 102

Brand: CADDY Pages: 2

Brand: CaddyStar Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands