Husqvarna 4421-DXL User Manual Download Page 58

Page: 58 / 68

Vehicle Specifications

VEHICLE SPECIFICATIONS

SPECIFICATIONS

HUV 4421-G;

HUV 4421-

GXP

HUV 4421-D;

HUV 4421-

DXP

HUV

4421-GXL

HUV

4421-

DXL

POWER SOURCE

GASOLINE

DIESEL

GASOLINE

DIESEL

Engine:

(Kawasaki) 4-cycle OHV, 675 cc, 23.0 maximum HP @3600 RPM (per

SAE J 1940/1349), twin-cylinder, air-cooled, with pressure lubrication system

•

Engine:

4-cycle OHV, 719 cc, 20.0 maximum HP @3600 RPM (per SAE J

1940/1349), three-cylinder, liquid-cooled, with pressure lubrication system

•

Fuel system:

Side-draft carburetor with float bowl, fixed jets, fuel filters, and

impulse fuel pump

•

Fuel system:

Mechanical injection, fuel water separator, fuel filters, and electric

fuel pump

•

Governor (Kawasaki engine):

internal to engine, centrifugal ball

•

Governor:

internal to engine, mechanical, centrifugal ball

•

Ignition:

Transistorized magneto

•

Ignition:

Compression

•

Transmission:

Forward and reverse with neutral (5.39:1 forward, 7.79:1

reverse)

•

Electrical system:

12 volt, 500 cca at 0 °F (-17.8 °C), 650 at 32 °F (0 °C).

105-minute reserve capacity and 35-amp charging capacity

•

Torque converter:

Automatic, variable-speed, dry type

•

STEERING/SUSPENSION/BRAKES

Suspension:

Front:

Independent double A-arms with coil-over shock absorbers

Rear:

Swing arms with coil-over shock absorbers

•

Steering:

Self-adjusting rack and pinion, Ackerman

•

Brakes

: Hydraulic brake system – brake pads and discs on each wheel with

separate foot-operated park brake

•

BODY/CHASSIS

Frame/Chassis:

Box tube aluminum

•

Side and rear body:

Plastic

•

Cargo bed:

Powder-coated steel or aluminum

•

Front body:

Geloy XTWM206

•

Tires: All Terrain:

25 x 10.5 – 12 front and rear; tubeless, 4-ply rated load range

Mud:

25 x 11 – 12 front and rear; tubeless, 4-ply rated load range

•

DIMENSIONS/WEIGHT

NOTE: Items marked with an asterisk (*) indicate approximate values.

*Overall length

(box bed configuration, without brush guard):

122 in. (309.9 cm)

154 in. (391.2 cm)

Page 56

HUV 4421 Owner’s Manual

Summary of Contents for 4421-DXL





































































Search results

Summary of Contents for 4421-DXL

Reviews:

Related manuals for 4421-DXL

Brands by name

Popular brands

Husqvarna 4421-DXL, User Manual

Search results

Summary of Contents for 4421-DXL

Reviews:

Related manuals for 4421-DXL

Brands by name

Popular brands