Husqvarna 4421-DXL User Manual Download Page 31 | Manualshive

Page: 31 / 68

background image

Towing with the Vehicle

B

D

A

C

B

D

A

C

197

Figure 12

Vehicle Load Capacity – Two-Passenger

Vehicles

198

Figure 13

Vehicle Load Capacity – Four-Passenger

Vehicles

TOWING WITH THE VEHICLE

WARNING

• Do not tow a vehicle or trailer on public streets or highways.

• Normal vehicle operating speed should be reduced when towing.

• Extreme caution should be used when towing.

• Do not allow riders in the vehicle or trailer being towed.

• Avoid sudden starts, sudden stops, and tight turns when towing.

• Avoid stopping on a hill when towing. If you must stop on a hill, avoid sudden starts, or rolling

backwards and stopping suddenly. Failure to heed this warning may cause vehicle to overturn,
possibly resulting in severe personal injury.

Towing another vehicle or a trailer can have adverse effects on vehicle handling. Be especially cautious when towing
other equipment with this vehicle.

See Vehicle Load Capacities on page 28 for vehicle capacity information.

Parking the vehicle with a trailer on a hill should be avoided. If you must park on a hill, apply the brakes and have
someone chock the trailer tires. The brakes should be released to allow the chocks to absorb the trailer load. After the
trailer tires have been chocked, engage the park brake.

TRANSPORTING ON A TRAILER

WARNING

• Gasoline vehicles only: Turn fuel shut-off valve to the closed (OFF) position (Figure 14).

• Do not allow riders in the trailer being towed.

• Avoid sudden starts, sudden stops, and tight turns when towing.

WARNING CONTINUED ON NEXT PAGE

HUV 4421 Owner’s Manual

Page 29

«
...
29
30
31
32
33
...
»

Summary of Contents for 4421-DXL





































































Reviews:

No comments

Related manuals for 4421-DXL

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 93

Brand: Yamaha Pages: 99

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 112

Kodiak YFM400FWK

Brand: Yamaha Pages: 167

Brand: Yamaha Pages: 193

Kodiak YFM45FAV

Brand: Yamaha Pages: 194

KODIAK 700 YFM70KDXH

Brand: Yamaha Pages: 178

KODIAK 700 YFM70KDHG

Brand: Yamaha Pages: 180

KODIAK Ultramatic

Brand: Yamaha Pages: 185

KODIAK 4X4 Ultramatic

Brand: Yamaha Pages: 185

KODIAK 450 Ultramatic

Brand: Yamaha Pages: 189

GRIZZLY YFM70GPAH

Brand: Yamaha Pages: 174

Brand: Yamaha Pages: 190

KODIAK 400 Ultramatic 4x4

Brand: Yamaha Pages: 187

GRIZZLY YFM700FWAD

Brand: Yamaha Pages: 182

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands