Husqvarna Viking Rose 605 Page 2 User Manual Download | Manualshive

Page: 2 / 64

background image

Instruction book Rose

2

This houshold sewing machine is designed to comply with IEC/EN 60335-2-28 and UL1594

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety precautions should always be
followed, including the following:
Read all instructions before using this household sewing machine.

DANGER

-

To reduce the risk of electric shock:

• A sewing machine should never be left unattended when plugged in. Always unplug

this sewing machine from the electric outlet immediately after using and before
cleaning.

• Always unplug before relamping. Replace bulb with same type rated 5 Watt.

WARNING

- To reduce the risk of burns, fire, electric

shock, or injury to persons:

• Do not allow to be used as a toy. Close attention is necessary when this sewing

machine is used by or near children or infirm persons.

• Use this sewing machine only for its intended use as described in this manual. Use

only attachments recommended by the manufacturer as contained in this manual.

• Never operate this sewing machine if it has a damaged cord or plug, if it is not

working properly, if it has been dropped or damaged, or dropped into water. Return
the sewing machine to the nearest authorised dealer or service center for
examination, repair, electrical or mechanical adjustment.

• Never operate the sewing machine with any air openings blocked. Keep ventilation

openings of the Sewing machine and foot controller free from the accumulation of
lint, dust, and loose cloth.

• Keep fingers away from all moving parts. Special care is required around the Sewing

machine needle.

• Always use the proper needle plate. The wrong plate can cause the needle to break.
• Do not use bent needles.
• Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
• Switch the sewing machine off (“0”) when making any adjustment in the needle

area, such as threading needle, changing needle, threading bobbin, or changing
presser foot, etc.

• Always unplug the sewing machine from the electrical outlet when removing covers,

lubricating, or when making any other user servicing adjustments mentioned in the
instruction manual.

• Never drop or insert any object into any opening.
• Do not use outdoors.
• Do not operate where aerosol (spray) products are being used or where oxygen is

being administrated.

• To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Hold plug when rewinding into cord reel. Do not allow plug to whip when

rewinding.

SAVE THESE INSTRUCTIONS

«
1
2
3
4
...
»

Summary of Contents for Rose 605

































































Reviews:

No comments

Related manuals for Rose 605

Brand: Banner Pages: 11

Brand: Baby Lock Pages: 198

Brand: ELNA Pages: 230

Brand: JUKI Pages: 75

Brand: Kärcher Pages: 55

Brand: Rtech Pages: 24

Brand: Singer Pages: 100

Brand: Garudan Pages: 89

Brand: A-S-S Pages: 7

Brand: Olivetti Pages: 16

ellegante 2 BLG2

Brand: Baby Lock Pages: 8

Brand: Brother Pages: 16

Brand: Brother Pages: 60

Brand: Brother Pages: 19

Entrepreneur Pro PR1050X

Brand: Brother Pages: 12

Entrepreneur W PR680W

Brand: Brother Pages: 10

Brand: Brother Pages: 66

Brand: Brother Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands