Husqvarna Viking Rose 605 User Manual Download

Page: 12 / 64

Instruction book Rose

Bobbin winding with the machine threaded

.
Make sure that the presser foot is up and the needle is in the highest position.

Note! Do not use a plastic presser
foot when bobbin winding.
1.

Place your empty bobbin with the

small mark

outwards on the

bobbin spindle on the front of the
machine.

Pull the thread from the needle

under the presser foot and to the
right over the thread guide (c).

Start from above and wind a few

turns of thread around the bob-
bin. Cut off the thread on the
thread knife (d).

Bring the bobbin spindle down.

Press the foot control. When the
bobbin winding is finished, the
bobbin will stop automatically.
Remove the bobbin, cut off the
thread and bring the bobbin
spindle up.

Note!

We do not recommend

winding specialty threads such as
clear nylon or other stretchy threads
through the needle. Instead see
"Bobbin winding - vertical spool
pin" below.

Place an

empty bobbin
with the mark

outwards

on the bobbin
spindle on the
front of the machine.

Place the large spool

holder under the thread
on the spool pin.

Bring the thread under the

thread guide (a) and over thread
guide (b),then

around

thread

guide (c) as illustrated.

From above

wind a few
turns of
thread
around the
bobbin and

into the knife.

. Bring the bobbin spindle

down. Press the foot control.
When the bobbin winding is
finished, the bobbin will stop

automatically. Remove the bob-
bin, cut off the thread and bring
the bobbin spindle up.

Bobbin winding - vertical spool pin

ocedur

Summary of Contents for Rose 605

































































Search results

Summary of Contents for Rose 605

Reviews:

Related manuals for Rose 605

Brands by name

Popular brands

Husqvarna Viking Rose 605, User Manual

Search results

Summary of Contents for Rose 605

Reviews:

Related manuals for Rose 605

Brands by name

Popular brands