background image

Instruction book Rose

50

Quilting

The "hand" look quilting stitch No

31 

, is a perfect stitch for relief

stitching. Use presser foot P.

1

. Mark the design on the top of the

fabric you are going to quilt.

2.

 Place the fabric you are going to

use as quilt backing, wrong side
up.

3

. Place a layer of batting on wrong

side. Finally place the top right
side up with the marking.

4.

 Pin all the pieces together.

5.

 Use transparent nylon thread as

upper thread and a synthetic
thread or embroidery thread as
bobbin thread.

6.

 Test sew. On the top side of your

work the triple stitch should be
filled with the bobbin thread and
the single stitch will not be visible
thanks to the transparent upper
thread.

7

. Sew along the marked quilt

design.

Applique

Use presser foot B.

1.

 Sew the heirloom applique stitch

number 33  , around a binding at

the edge, or for hand look
applique.

2.

 The satin stitch number 38 

, set

to stitch width 2 mm sews
beautiful appliques. Fuse or pin
applique in place and satin stitch
around the outside edges.

3.

 Use stitch number 32 

 to quilt.

Sew the stitches with a few cm in
between.

Se

wing

Summary of Contents for Rose 605

































































Reviews: