background image

Appendix C • Standards compliance

 

114

1039434-0001  Revision A

Users should ensure for their own protection that the electrical ground connections 
of the power utility, telephone lines, and internal metallic water pipe system, if 
present, are connected together. This precaution may be particularly important in 
rural areas. 

Users should not attempt to make electrical ground connections themselves, 
but should contact the appropriate electrical inspection authority, or electrician, 
as appropriate.

Electromagnetic interference (EMI)

This product conforms to EMI standards of the U.S. FCC, Canadian CSA, and European 
Union (EU), as detailed in the following sections. The installation and maintenance 
procedures in the installation guide must be followed to ensure compliance with 
these regulations. 

This is a class B product. In a domestic environment, this product may cause 
radio interference, in which case the user may be required to take adequate 
measures.

FCC Part 15

This section applies to the HN9260 satellite modem. 

Standards to which conformity is declared: FCC Part 15

The modem complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, and (2) 
this device must accept any interference received, including interference that may 
cause undesired operation.

Responsible party’s name: Hughes Network System, LLC 

Address: 11717 Exploration Lane, Germantown, MD 20876

Telephone: 1 (866) 347-3292

Trade name: HUGHES

Type of equipment: Two-way Hughes system

<<Need HN9260 model number>>

Model number: HN9260 (1502573-xxxx)

DANGER

NOTICE

Summary of Contents for HN9260



























































































































Reviews: