Hughes Network HN9260 Installation Manual Download

Page: 40 / 122

Chapter 4 • Commissioning the satellite modem

1039434-0001 Revision A

Entering satellite parameters (manual entry)

This is an

alternate

method for entering the satellite parameters. You must use this

method if the satellite and transponder for your installation are not listed in the
drop-down list in

Figure 18

and you were not provided with an

sbc.cfg

file.

Skip this section if you selected a satellite and transponder on the Satellite
Parameters screen.

The satellite parameters are provided to you in a technical update email or other
communication.

To enter the parameters:

1. On the Satellite Parameters screen, select the Enter satellite parameters

manually checkbox shown in

Figure 20

2. Click

Next

Figure 20: Satellite Parameters screen

Summary of Contents for HN9260



























































































































Search results

Summary of Contents for HN9260

Reviews:

Related manuals for HN9260

Brands by name

Popular brands

Hughes Network HN9260, Installation Manual

Search results

Summary of Contents for HN9260

Reviews:

Related manuals for HN9260

Brands by name

Popular brands