Hughes Network HN9260 Installation Manual Download

Page: 66 / 122

Chapter 5 • Completing the installation

1039434-0001 Revision A

1. Open the System Control Center home page in a web browser.

Note:

The method described here works for Internet Explorer. For other browsers

see the browser’s instructions for creating a shortcut to a URL.

2. Drag the icon that appears in front of the address displayed in the browser to the

computer desktop.

Figure 49: Icon used to create shortcut

Installation complete

If you have successfully followed all previous instructions, at this point the satellite
modem is installed, commissioned, and activated.

The remaining information in this

installation guide is provided for reference or troubleshooting purposes. You may
or may not need it.

Once the satellite modem installation is complete, the customer can connect an
Ethernet hub, router, or switch to the HN9260 modem to support multiple
computers on a LAN, using the address information shown in on the System
Information page (

System Info page

on page 81).

Summary of Contents for HN9260



























































































































Search results

Summary of Contents for HN9260

Reviews:

Related manuals for HN9260

Brands by name

Popular brands

Hughes Network HN9260, Installation Manual

Search results

Summary of Contents for HN9260

Reviews:

Related manuals for HN9260

Brands by name

Popular brands