Hughes Network HN9260 Installation Manual Download

Page: 51 / 122

Chapter 4 • Commissioning the satellite modem

1039434-0001 Revision A

does not support ACP, ACP is not enabled at the NOC, or there is a problem
with the ACP server.

Note:

The ACP test is required for Ku-band customers in the United States and

Canada; for customers outside the United States and Canada, it is optional.

2. Click

Next

3. On the Transmit Antenna Pointing screen, click

Manual

to initiate the manual

cross-polarization test.

Figure 32: Initiating a manual cross-polarization test

Be ready to adjust the antenna. For antenna adjustment instructions, see the
antenna installation guide.

Note:

The manual cross-polarization test times out 3 to 5 minutes after you click the

Manual

button. Therefore you must complete any antenna adjustments

required to achieve maximum transmit isolation within this time.

Summary of Contents for HN9260



























































































































Search results

Summary of Contents for HN9260

Reviews:

Related manuals for HN9260

Brands by name

Popular brands

Hughes Network HN9260, Installation Manual

Search results

Summary of Contents for HN9260

Reviews:

Related manuals for HN9260

Brands by name

Popular brands