Huawei TaiShan 200 Series User Manual Download Page 17

Page: 17 / 132

Drive

Filler panel

USB 3.0 port

VGA port

Label plate with

an SN label

Servers with Kunpeng 920 5220 or 3210 processors do not support the configuration

of 24 x 2.5-inch SAS/SATA pass-through drives.

Table 2-1 Description of ports on the front panel

Port

Type

Description

USB port

USB 3.0

The USB ports allow USB devices to be

connected to the server.

NOTE

● Before connecting an external USB device,

check that the USB device functions properly.

A server may operate abnormally if an

abnormal USB device is connected.

● If an external USB device is used, the

maximum length of the extension cable is 1

VGA port

DB15

The VGA port is connected to a terminal,

such as a monitor or physical KVM.

NOTE

The VGA port on the front panel does not have

cable screws. The VGA cable is easy to fall off.

You are advised to use the VGA port on the rear

panel.

The serial number (SN) on the label is a string that uniquely identifies a server.

The SN is required when you contact Huawei technical support.

Figure 2-5

shows the SN format.

Figure 2-5 SN example

TaiShan 200 Server

User Guide (Model 2280)

2 Components

Issue 04 (2020-01-16)

Summary of Contents for TaiShan 200 Series





































































































































Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands

Huawei TaiShan 200 Series, User Manual

Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands