Huawei TaiShan 200 Series User Manual Download Page 99

Page: 99 / 132

5.10.10 Upgrading the System

Upgrade server drivers, firmware, and management software as needed.

Obtaining Documents

TaiShan Rack Server Upgrade Guide
TaiShan iDriver V100R001C00 Driver Version Mapping
Release Notes

Upgrading Firmware or Management Software

Upgrade the raid card firmware, mainboard CPLD and drive backplane CPLD on

the iBMC WebUI. For details, see the

TaiShan Rack Server Upgrade Guide

Updating Drivers

If the existing driver versions on a server are inconsistent with those in the driver

version mapping, install the drivers of required versions. Otherwise, the server may

operate abnormally. For details, see the OS installation guide.

TaiShan 200 Server

User Guide (Model 2280)

5 Install and Configure

Issue 04 (2020-01-16)

Summary of Contents for TaiShan 200 Series





































































































































Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands

Huawei TaiShan 200 Series, User Manual

Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands