Huawei TaiShan 200 Series User Manual Download Page 94

Page: 94 / 132

Set the PXE

●

Setting the PXE for an LAN on motherboard (LOM)
a. Select Advanced and press Enter.

The Advanced screen is displayed, as shown in

Figure 5-47

Figure 5-47 Advanced screen

b. Select LOM Configuration > PXE Configuration and press Enter.
c.

Set the PXE for NICs.
i.

Select the network port such as PXE1 Configuration, and press

Enter.

ii. In the dialog box that is displayed, select Enable and press Enter.

d. Select PXE Boot Capability and press Enter. In the dialog box that is

displayed, select the PXE boot network protocol.

▪

UEFI: IPv4

▪

UEFI: IPv6

▪

UEFI: IPv4/IPv6

e. Press F10.

The system displays "Save configuration changes and reset and exit?"

Select Yes and press Enter to save the setting.

●

Setting the PXE for a NIC connected to the server

The displayed information varies according to the external NIC when you configure

the PXE. The following procedure uses the SP570 NIC as an example.

TaiShan 200 Server

User Guide (Model 2280)

5 Install and Configure

Issue 04 (2020-01-16)

Summary of Contents for TaiShan 200 Series





































































































































Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands

Huawei TaiShan 200 Series, User Manual

Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands