Huawei TaiShan 200 Series User Manual Download Page 83

Page: 83 / 132

5.10.5 Checking the Server

Check the server in the sequence shown in

Figure 5-33

. The method to be used

depends on the actual situation.

For details about CLI commands, see the

TaiShan Rack Server iBMC User Guide

Figure 5-33 Checking the server

Procedure

Step 1 Check indicator status.

Ensure that hardware devices are working correctly.

For details, see

2.2 Front Panel Indicators and Buttons

and

2.4 Rear Panel

Indicators

Step 2 Check the server.

●

Check the server using the iBMC WebUI.
a. Log in to the iBMC over the WebUI. For details, see

5.10.4 Logging In to

the iBMC WebUI

You are advised to change the initial password when logging in to the iBMC for

the first time. For details, see

5.10.6 Changing Initial Passwords

TaiShan 200 Server

User Guide (Model 2280)

5 Install and Configure

Issue 04 (2020-01-16)

Summary of Contents for TaiShan 200 Series





































































































































Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands

Huawei TaiShan 200 Series, User Manual

Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands