Huawei TaiShan 200 Series User Manual Download Page 40

Page: 40 / 132

Item

Server Powered by Kunpeng

920 7260, 5250, or 5230

Processors

Server Powered by Kunpeng

920 5220 or 3210 Processors

Memory

● Maximum number of slots:

32 DDR4 slots supporting

RDIMMs

● Maximum memory speed:

2933 MT/s

● Memory protection

functions: ECC, SEC/DED,

SDDC, and patrol scrubbing

● Capacity of a single DIMM:

16 GB, 32 GB, 64 GB, or

128 GB

NOTE

DIMMs of different specifications

(such as the capacity, bit width,

rank, and height) cannot be

installed in one server. That is, all

DIMMs on one server must have

the same part No.

● Maximum number of slots:

16 DDR4 slots supporting

RDIMMs

● Maximum memory speed:

2933 MT/s

● Memory protection

functions: ECC, SEC/DED,

SDDC, and patrol scrubbing

● The capacity of a single

DIMM can be 16 GB, 32 GB,

and 64 GB.

NOTE

DIMMs of different specifications

(such as the capacity, bit width,

rank, and height) cannot be

installed in one server. That is, all

DIMMs on one server must have

the same part No.

Storage

Drive:
● Support for a variety of drive configurations. For details, see

Table 2-9

● Hot swap of a single drive.
RAID controller card:
● Support for a variety of RAID controller cards. Use the

Intelligent Computing Compatibility Checker

to obtain

information about the specific RAID controller cards

supported.

● Supercapacitor to protect cache data from power failures,

and support for RAID level migration, drive roaming, self-

diagnosis, and web-based configuration. For details about

the RAID controller card, see the

TaiShan Server RAID

Controller Card User Guide

FlexIO card

A maximum of two FlexIO cards. A FlexIO card can provide

either of the following network ports:
● Four GE electrical ports, supporting PXE
● Four 25GE/10GE optical ports, supporting PXE

NOTE

Different optical modules can be used to support 25GE or 10GE

optical port rate.

TaiShan 200 Server

User Guide (Model 2280)

3 Product Specifications

Issue 04 (2020-01-16)

Summary of Contents for TaiShan 200 Series





































































































































Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands

Huawei TaiShan 200 Series, User Manual

Search results

Summary of Contents for TaiShan 200 Series

Reviews:

Related manuals for TaiShan 200 Series

Brands by name

Popular brands