Huawei STS-6000K-H1 Installation Manual Download Page 74 | Manualshive

Page: 74 / 77

background image

STS-6000K-H1 Smart Transformer Station (Vietnam,
Duc Long Gai Lai)
Installation Guide

A FAQ

Issue 02 (2020-02-21)

Copyright © Huawei Technologies Co., Ltd.

68

Supplier

Purpose

Paint Model

EPICON ZINC SC B-2 M(ON LINE ZINC)

Intermediate coat: EPICON SC PRIMER GREY
CSC-9107

Top coat: UNYMARINE SC FINISH WHITE
CSC-9205 (RAL-9003)

Logo

Red: UNYMARINE SC MARKING RAL-3020

Black: UNYMARINE SC MARKING
RAL-9005

A.2 Requirements for the STS-6000K-H1 Foundation
Dimensions



Construct a foundation of the correct dimensions based on the site design drawing. The
preceding figure is for reference only.



Unmarked sizes shall be determined according to onsite conditions.



Reserve pressure relief channels for the ring main unit, and add protective measures to
prevent high temperature gas from burning nearby personnel during pressure relief.



The ladder should not block the low voltage and MV cables in and out. The insulation
ladder is recommended to be put in front of the door when maintenance.

The technical requirement:



The size of each cement column is recommended to be no less than 6218 mm x 600 mm,
and the container shall be placed in the center of the foundation. Height of the column
shall be determined according to the actual situation on site.



The outline of the smart transformer station is 6058 mm (L) x 2438 mm (W).



Weight of STS-6000K-H1 is no more than 22 t and transformer oil is mineral oil,
noncorrosive. And the volume of transformer oil is about 3850 L (about 3.4 t).

«
...
72
73
74
75
76
...
»

Summary of Contents for STS-6000K-H1














































































Reviews:

No comments

Related manuals for STS-6000K-H1

Brand: Balluff Pages: 62

Brand: Balluff Pages: 105

DigitalFlow XGF868i

Brand: Panametrics Pages: 72

DigitalFlow XGF868i

Brand: Panametrics Pages: 90

Brand: J&E Hall Pages: 10

Brand: Yaesu Pages: 15

Brand: Yaesu Pages: 99

Brand: Yaesu Pages: 20

Brand: Yaesu Pages: 176

Brand: BBC Bircher Pages: 4

Brand: MKS Pages: 55

Brand: Zhongshan K-mate General Electronics Pages: 5

Brand: Radio Shack Pages: 44

Brand: Vertex Pages: 66

BTL7-A/E1 0-M-H-SA262-KA Series

Brand: Balluff Pages: 16

THERMASGARD ETM 5

Brand: S+S Regeltechnik Pages: 16

Brand: IMG STAGE LINE Pages: 22

MDS iNET-II 900

Brand: GE MDS Pages: 190

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands