Huawei ME936 Hardware Manual Download Page 8

Page: 8 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Overall Description

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Overall Description

2.1 About This Chapter

This chapter gives a general description of the ME936 module and provides:



Function Overview



Circuit Block Diagram

2.2 Function Overview

Table 2-1

Features

Feature

Description

Physical
Features



Dimensions (L × W × H): 42 mm × 30 mm × 2.3 mm



Weight: about 6 g

Operating
Bands

LTE: BI/B2/B3/B4/B5/B7/B8/B13/B17/B20

WCDMA/HSDPA/HSUPA/HSPA+: 850 MHz/900 MHz/1700 MHz
(AWS)/1900 MHz/2100 MHz

GPRS/EDGE: 850 MHz/900 MHz/1800 MHz/1900 MHz

GPS/GLONASS: L1

Operating
Temperature

Normal operating temperature:

–10°C to +55°C

Extended operating temperature

[1]

–20°C to +70°C

Storage
Temperature

–40°C to +85°C

Moisture

RH5% to RH95%

Power
Voltage

3.135 V to 4.4 V (3.3 V is typical)

AT
Commands

See the

HUAWEI ME936 LTE M.2 Module AT Command

Interface Specification

Application

USIM (3.0 V or 1.8 V)

Summary of Contents for ME936


















































































Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands

Huawei ME936, Hardware Manual

Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands