Huawei ME936 Hardware Manual Download Page 56

Page: 56 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Electrical and Reliability Features

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Table 5-2

Operating and storage temperatures and humidity for the ME936 module

Specification

Min.

Max.

Unit

Normal working temperatures

[1]

–10

+55

°C

Extended temperatures

[2]

–20

+70

°C

Ambient temperature for storage

–40

+85

°C

[1]: When the ME936 module works at this temperature, all its RF indexes comply with the
3GPP TS 45.005 specifications.

[2]: When the ME936 module works at this temperature,

NOT

all its RF indexes comply with

the 3GPP TS 45.005 specifications.

5.4 Power Supply Features

5.4.1

Input Power Supply

Table 5-3 lists the requirements for input power of the ME936 module.

Table 5-3

Requirements for input power for the ME936 module

Parameter

Min.

Typ.

Max.

Ripple

Unit

3.3V

3.135

3.3

4.4

0.05

Figure 5-1

Power Supply During Burst Emission

The minimum value of the power supply must be guaranteed during the burst (with 2.5 A Peak
in GPRS or EGPRS mode).

Summary of Contents for ME936


















































































Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands

Huawei ME936, Hardware Manual

Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands