Huawei ME936 Hardware Manual Download Page 57

Page: 57 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Electrical and Reliability Features

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Table 5-4

Requirements for input current of the ME936 module

Power

Peak (Maximum)
Max Avg@100uS

Normal (Maximum)
Max Avg@1S

3.3V

2500 mA

1100 mA

5.4.2

Power Consumption

The power consumption of ME936 in different scenarios are respectively listed in
Table 5-5 to Table 5-9 .

The power consumption listed in this section are tested when the power supply of
ME936 module is normal voltage (3.3 V), and all of test values are measured at room
temperature.

Table 5-5

Averaged power off DC power consumption of ME936

Description

Test Value (uA)

Notes/Configuration

Typical

Power off

150

Normal voltage (3.3 V) is ON and
Power_On_Off pin is pulled low

Table 5-6

Averaged standby DC power consumption of ME936

(WCDMA/HSDPA/LTE/GSM)

Description

Bands

Test Value (mA) Notes/Configuration

Typical

Sleep

LTE

(sleep)

LTE bands

2.4

Module is powered up.

DRX cycle=8 (2.56s)

Module is registered on
the network.

USB is in suspend.

HSPA+/WCD
MA

(sleep)

UMTS
bands

2.2

Module is powered up.

DRX cycle=8 (2.56s)

Module is registered on
the network.

USB is in suspend.

GPRS/EDGE

(sleep)

GSM
bands

2.3

Module is powered up.

MFRMS=5 (1.175s)

Module is registered on
the network.

USB is in suspend.

Summary of Contents for ME936


















































































Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands

Huawei ME936, Hardware Manual

Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands