Huawei ME936 Hardware Manual Download Page 31

Page: 31 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Description of the Application Interfaces

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

3.4.5

W_DISABLE# Pin

ME936 provides a hardware pin (W_DISABLE#) to enable/disable the radio function.
This function also can be implemented by AT command.

Table 3-6

Function of the W_DISABLE# pin

No.

W_DISABLE#

Function

Low

WWAN function will be turned off.

High

WWAN function is determined by software AT
command. Default enabled.

Floating

WWAN function is determined by software AT
command. Default enabled.

Figure 3-17

Connections of the W_DISABLE# pin

It is not recommended to add a diode on the W_DISABLE# pin outside the ME936
module.

3.4.6

GPS_DISABLE# Pin

ME936 provides a hardware pin (GPS_DISABLE#) to enable/disable the GPS
function.

Table 3-7

Function of the GPS_DISABLE# pin

No.

GPS_DISABLE#

Function

Low

GPS function is disabled.

High

GPS function is determined by software AT
command. Default enabled.

Module
(Modem)

BB Chip

1.8V

W_DISABLE#

VCC From Host

10 kΩ

Host

Summary of Contents for ME936


















































































Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands

Huawei ME936, Hardware Manual

Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands