Huawei ME936 Hardware Manual Download Page 14

Page: 14 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Description of the Application Interfaces

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Pin
No.

Pin Name

Pad
Type

Description

Parameter

Min.(
V)

Typ.(
V)

Max.(
V)

Comments

Notch

Reserved

Reserved for Future Use,
please keep it

NC in host side.

CONFIG_0

Not Connected internally.

ME936 is configured as
WWAN-SSIC 0.

Reserved

Reserved for Future Use,
please keep it NC in host
side.

Wake_On_
WWAN#

It is open drain and active
low.

WWAN to wake up the
host.

0.48

=75 mA

Reserved

Reserved for Future Use,
please keep it NC in host
side.

BodySAR_N

Hardware pin for BodySAR
Detection, active low.

H: No TX power backoff
(default).

L: TX power backoff.

1.26

3.6

ME936 is
pulled up
inside.

–0.3

0.3

GPS_DISAB
LE#

GPS disable function

H: GPS function is
determined by software AT
command. Default
enabled.

L: GPS is turned off.

1.26

3.6

ME936 is
pulled up
inside.

–0.3

0.3

Ground

Not Connected

UIM_RESET

USIM Reset

0.7 x
UIM_
PWR

3.3

UIM_PWR
=1.8 V or
2.85 V

0.2 x
UIM_
PWR

Not Connected

Summary of Contents for ME936


















































































Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands

Huawei ME936, Hardware Manual

Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands