Huawei ME936 Hardware Manual Download Page 40

Page: 40 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Description of the Application Interfaces

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Take care that we should use the software section and hardware section together.
Software section is used to debug the function and create the GPIO configuration.
Hardware section is used to control the antenna.

Table 3-11

List of ANTCTL pins

Pin
No.

Pin Name

Pad
Type

Description

Parameter

Min.(
V)

Typ.(
V)

Max.(
V)

Comments

ANTCTL0

Tunable antenna
control signal, bit 0.

It is a push-pull type
GPIO.

1.35

1.8

0.45

ANTCTL1

Tunable antenna
control signal, bit 1.

It is a push-pull type
GPIO.

1.35

1.8

0.45

ANTCTL2

Tunable antenna
control signal, bit 2.

It is a push-pull type
GPIO.

1.35

0.45

ANTCTL3

Tunable antenna
control signal, bit 3.

It is a push-pull type
GPIO.

1.35

1.8

0.45

3.8 Config Pins

The module provides 4 config pins. ME936 is configured as WWAN-SSIC 0.

Table 3-12

List of CONFIG pins

Pin
No.

Pin Name

Pad Type Description

Parameter

Min.(
V)

Typ.(
V)

Max.(
V)

Comments

CONFIG_3

Connected to Ground
internally.

ME936 is configured as
WWAN-SSIC 0.

CONFIG_0

Not Connected
internally.

ME936 is configured as
WWAN-SSIC 0.

Summary of Contents for ME936


















































































Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands

Huawei ME936, Hardware Manual

Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands