Huawei ME936 Hardware Manual Download Page 23

Page: 23 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Description of the Application Interfaces

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Pin
No.

Pin Name

Pad
Type

Description

Parameter

Min.(
V)

Typ.(
V)

Max.(
V)

Comments

H: No TX power backoff
(default).

L: TX power backoff.

–0.3

0.3

inside.

SIM_DET

SIM hot swap detection pin.

Rising edge for insertion;
falling edge for removal.

H: SIM is present.

L: SIM is absent.

1.26

1.8

2.1

ME936 is
pulled up
inside.

–0.3

0.63

3.4.2

Power_On_Off Control Pin

The ME936 module can be controlled to be powered on/off by the Power_On_Off pin.

Table 3-4

Two states of Power_On_Off pin

Item Pin state Description

High

ME936 is powered on.

NOTE: If ME936 needs to be powered on automatically, the
Power_On_Off pin must be pulled up to 3.3 V.

Low

ME936 is powered off.

It is internally pulled to low.

ME936 is powered by regulated 3.3 V

If ME936 is powered by 3.3 V voltage regulator (such as notebook or Ultrabook),
Power_On_Off pin should be pulled up to 3.3 V through a resistor.

The pull-up resistor should be

not larger than 10 k

The following are the power On/Off sequences:

1. The module gets 3.3 V when power supply for the module is switched on.

2. The module is turned on since Power_On_Off pin is pulled up directly to 3.3 V.

3. Host cuts off 3.3 V supply to power off the module.

The recommended circuit is shown as in Figure 3-5 .

Summary of Contents for ME936


















































































Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands

Huawei ME936, Hardware Manual

Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands