Huawei ME936 Hardware Manual Download Page 27

Page: 27 / 81

HUAWEI ME936 LTE M.2 Module
Hardware Guide

Description of the Application Interfaces

Issue 03 (2017-12-11)

Huawei Proprietary and Confidential

Figure 3-11

Recommended warn boot timing in the notebook/tablet

If there is a limitation on the controlling GPIO to be programmable 500 ms, the
following hardware solution can be used, as shown in Figure 3-12 .

Figure 3-12

Power on/off circuit (hardware solution)

3.3V (battery,
always on)

RESET#

Power_On_Off

Warn boot in the notebook/tablet

≥ 500 ms

ME936

Pin6

HOST

VCC

GPIO2

NMOS

3.3V

(battery)

GPIO2

Power_On_Off

VCC

GPIO2

is the power domain of the GPIO2.

When

VCC

GPIO2

, Q2 is on and Q1 is off. So the Pin6 is controlled by

GPIO2 of host.
When

VCC

GPIO2

Off

, Q2 is off and Q1 is on. So the Pin6 is pulled low,

then the module is powered off.

Summary of Contents for ME936


















































































Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands

Huawei ME936, Hardware Manual

Search results

Summary of Contents for ME936

Reviews:

Brands by name

Popular brands