Huawei IPC6125-WDL-FA Configuration Manual Download Page 83

Page: 83 / 202

Procedure

Step 1

Choose

Settings

Network Configuration

IP Filter

The

IP Filter

page is displayed, as shown in

Figure 7-5

IP Filter page

Step 2

To enable the IP filter function, select

Enable

Step 3

Select an IP filter rule as required from the drop-down list box.
The IP filter rule has two options:

Deny

and

Allow

, that is, denying or allowing the access of

IP data packets coming from a specified IP network segment, port, or using a specified
protocol, to the IPC.

Step 4

Click

Add

Step 5

Set

IP address

Subnet mask

Port range

, and

Protocol type

in the

Add filter rule

page, as

shown in

Figure 7-6

Add filter rule page

NOTE

Both the start and end port numbers must be within the range of 0 to 65535. The start port number must
be equal to or less than the end port number.

If you select

All

, all port numbers within the range of 0 to 65535 are filtered.

If a filter rule shown in

Figure 7-6

is configured under

Deny

, the IPC does not process TCP packets

received on port

from

192.168.0.200

Step 6

Click

The

IP Filter

page is displayed.

Step 7

Click

Save

IPC6125-WDL-FA
Configuration Guide

7 Setting Network Parameters

Issue 01 (2016-08-20)

Huawei Proprietary and Confidential

Summary of Contents for IPC6125-WDL-FA











































































































































































































Search results

Summary of Contents for IPC6125-WDL-FA

Reviews:

Related manuals for IPC6125-WDL-FA

Brands by name

Popular brands

Huawei IPC6125-WDL-FA, Configuration Manual

Search results

Summary of Contents for IPC6125-WDL-FA

Reviews:

Related manuals for IPC6125-WDL-FA

Brands by name

Popular brands