Huawei IPC6125-WDL-FA Configuration Manual Download Page 66

Page: 66 / 202

Parameter

Description

NOTE

When

White balance mode

is set to

Auto

, you can drag the

sliders or enter values in the spin boxes to adjust the blue
and red fine-tune offset values. These values are integers
ranging from 0 to 255.

When

White balance mode

is set to

Manual

, you can drag

the sliders or enter values in the spin boxes to adjust the
blue and red intense-tune offset values. These values are
integers ranging from 0 to 255.

It is recommended that you use the

Auto

mode.

Noise reduction switch

Indicates whether to enable the noise reduction function.
The options are as follows:

Disable

: Disable the noise reduction function.

Normal mode

(default): You can set

Noise reduction

level

when you set

Noise reduction switch

Normal mode

. A higher noise reduction level

indicates better noise reduction effect but lower
image definition.

Expert mode

: You can set

Temporal noise

reduction level

and

Spatial noise reduction level

when you set

Noise reduction switch

Expert

mode

Spatial noise reduction level

: A higher spatial noise

reduction level indicates better noise reduction effect.
Object edges are smooth, but the image clarity
decreases.

Temporal noise reduction level

: A higher temporal

noise reduction level indicates better noise reduction
effect. The image noise is less, but the image clarity
decreases.

Brightness

Indicates an attribute of visual perception in which a
source appears to be radiating or reflecting light.

Hue

Indicates the degree to which a stimulus can be described
as similar to or different from stimuli that are described
as red, green, blue, and yellow.

Saturation

Indicates the colorfulness of a color relative to its own
brightness.

Contrast

Contrast is the ratio of black and white colors in an
image.

Increasing the contrast improves the image clarity
and color brightness.

Decreasing the contrast dims the entire image.

Sharpness

Sharpness reflects the image clarity and edge sharpness.

Reset

Used to restore the ISP parameters to default values.

IPC6125-WDL-FA
Configuration Guide

6 Setting Video Parameters

Issue 01 (2016-08-20)

Huawei Proprietary and Confidential

Summary of Contents for IPC6125-WDL-FA











































































































































































































Search results

Summary of Contents for IPC6125-WDL-FA

Reviews:

Related manuals for IPC6125-WDL-FA

Brands by name

Popular brands

Huawei IPC6125-WDL-FA, Configuration Manual

Search results

Summary of Contents for IPC6125-WDL-FA

Reviews:

Related manuals for IPC6125-WDL-FA

Brands by name

Popular brands