Huawei IPC6125-WDL-FA Configuration Manual Download Page 53 | Manualshive

Page: 53 / 202

background image

Parameter

Description

Dynamic bit rate

You can set the dynamic bit rate only when you set

Coding

protocol

to

H.264

or

H.265

.

After you set the dynamic bit rate, the camera will automatically use
the dynamic bit rate to deliver more clear live video or recordings
when an alarm is generated. After that alarm is cleared, the camera
restores the bit rate you set for the data stream.

NOTE

l

It is recommended that you set the dynamic bit rate to a value greater
than the bit rate you set for the data stream.

l

The dynamic bit rate is valid only for primary streams.

Water mark

You can select it to enable the watermark function to protect
information security, trace the anti-counterfeit, and protect the
copyright.

Full frame rate

The full frame rate is a frame rate that the IPC collects using a
sensor or chip.

NOTE

The full frame rate must be greater than or equal to the frame rate you set for
the data stream.

Layered encoding

You can set layered encoding only when you set

Coding protocol

to

H.264

or

H.265

.

To enable layered encoding, select

Layered encoding

.

Coding protocol

Set the coding protocol based on the site requirements. The options
are as follows:

l

H.264

: The H.264 protocol requires relatively small bandwidth

to ensure the video quality.

l

MJPEG

: The MJPEG protocol decodes and displays each frame

independently without referring to the previous and next frames.
This protocol has a small compression ratio and requires large
bandwidth to ensure the video quality. This protocol is suitable
for video editing.

l

H.265

: The H.265 protocol is bandwidth-conserving compared

with the H.264 protocol.

NOTE

l

Before connecting cameras to a surveillance platform, ensure that the
surveillance platform supports coding protocols on cameras to properly
play live video and record video. If the surveillance platform does not
support coding protocols on cameras, change the coding protocols on the
cameras to that supported by the surveillance platform.

l

Local recordings and SD card recordings support the H.264 and H.265
protocols.

IPC6125-WDL-FA
Configuration Guide

6 Setting Video Parameters

Issue 01 (2016-08-20)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

47

«
...
51
52
53
54
55
...
»

Summary of Contents for IPC6125-WDL-FA











































































































































































































Reviews:

No comments

Related manuals for IPC6125-WDL-FA

EF 24mm f/2.8 IS USM

Brand: Canon Pages: 2

EF14mm f/2.8L II USM

Brand: Canon Pages: 2

EF24-105MM F/4L IS USM

Brand: Canon Pages: 21

EF100-400mm f/4.5-5.6L IS II USM

Brand: Canon Pages: 21

Speedlite 600EX-RT

Brand: Canon Pages: 2

EF-S18-135mm f/3.5-5.6 IS STM

Brand: Canon Pages: 11

Speedlite 420EX

Brand: Canon Pages: 13

EF 70-200mm f/2.8L IS II USM

Brand: Canon Pages: 2

EF 70-200mm f/2.8L IS II USM

Brand: Canon Pages: 17

Macro Twin Light MT-26EX-RT

Brand: Canon Pages: 128

Speedlite 600EX-RT

Brand: Canon Pages: 372

EF-S10-18mm f/4.5-5.6 IS STM

Brand: Canon Pages: 16

EF24-70mm f/2.8L USM

Brand: Canon Pages: 11

Brand: Canon Pages: 22

PowerShot S400 Digital Elph

Brand: Canon Pages: 2

PowerShot S230 DIGITAL ELPH

Brand: Canon Pages: 2

PowerShot S110 Digital ELPH

Brand: Canon Pages: 7

Brand: Canon Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands