Huawei IPC6125-WDL-FA Configuration Manual Download Page 136 | Manualshive

Page: 136 / 202

background image

Context

l

Ensure that the camera lens is not blocked by objects, for example, leaves and columns,
to effectively and continuously track the object. Do not directly place the camera lens
opposite to a light source, water surface, or reflection plane, to prevent interference or
false alarms.

l

Before configuring the intelligent analysis function, ensure that the camera lens is
focused accurately, video images are clear, and light conditions are proper. If the
illuminance is lower than 20 lux, or video images are not clear with much noise, set
artificial light sources for light compensation to ensure even and proper light.

l

During the intelligent analysis test, the angle between the horizontal view angle of the
camera (that is, the optic normal of the camera lens) and the level ground or plane of the
monitoring object (for example, wall), must be greater than 15 degrees (reference: 30
degrees to 45 degrees) to ensure that the top of the monitoring object is covered.

l

The camera installation height must be determined based on the site requirements
(reference: 5 m to 6 m for tilted installation and 3 m to 5 m for vertical installation). A
proper installation height can ensure that the object size displayed in video images is
greater than the minimum object size and less than the maximum object size. It is
recommended that the object size be 1/8 to 1/3 of the image size.

l

It is recommended that

Frame rate

be set to

10

or higher on

Settings

>

Channel

Configuration

>

Video&Stream Parameters

to prevent impact on the behavior

analysis effect, for example, the object box is lost, the object box does not match the
object size, or all object boxes are displayed with delay.

Procedure

Step 1

Choose

Settings

>

Intelligent Analysis

>

Behavior Analysis Parameters

.

The

Behavior Analysis Parameters

page is displayed, as shown in

IPC6125-WDL-FA
Configuration Guide

9 Setting Intelligent Analysis Parameters

Issue 01 (2016-08-20)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

130

«
...
134
135
136
137
138
...
»

Summary of Contents for IPC6125-WDL-FA











































































































































































































Reviews:

No comments

Related manuals for IPC6125-WDL-FA

Brand: Samsung Pages: 1

Brand: VADDIO Pages: 13

Brand: VADDIO Pages: 5

Brand: VADDIO Pages: 18

ClearSHOT 10 USB

Brand: VADDIO Pages: 62

Brand: VADDIO Pages: 41

DH-IPC-HFW1200SP-W

Brand: Delta Pages: 6

Brand: RDI Technology Pages: 16

Brand: ALIBI Pages: 2

Brand: Gentec-E Pages: 94

Brand: ViewSonic Pages: 4

Brand: HIKVISION Pages: 184

Brand: Navman Pages: 16

Brand: Dalsa Pages: 116

ShortCam LC-AS21 Mini

Brand: Launch Pages: 9

Brand: Bronica Pages: 36

Brand: Spycentre Security Pages: 2

Brand: GE Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands