Huawei FusionModule1000A20 Installation Manual Download

Page: 73 / 107

FusionModule1000A20 Prefabricated All-in-One Data
Center
Installation Guide

6 Installing Devices Inside the Pre-fab. Module

Issue 02 (2020-01-15)

Context

The ASD power box and batteries inside the pre-fab. module have been installed before
delivery. You only need to connect the reserved cables to the batteries onsite.

Preparations

Tools: Phillips screwdriver

Materials: none

Skill requirement: common technician

Procedure

Step 1

Open the power box using a key.

Step 2

Remove the protective foam from the battery and check whether the battery is intact or leaks.

If the battery is damaged or leaks, contact Huawei technical support to replace the battery.

Step 3

Connect the reserved battery cable.

Distinguish the positive and negative battery terminals when connecting a battery cable.

Figure 6-35

ASD battery wiring diagram

Summary of Contents for FusionModule1000A20












































































































Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands

Huawei FusionModule1000A20, Installation Manual

Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands