Huawei FusionModule1000A20 Installation Manual Download Page 54

Page: 54 / 107

FusionModule1000A20 Prefabricated All-in-One Data
Center
Installation Guide

6 Installing Devices Inside the Pre-fab. Module

Issue 02 (2020-01-15)

----End

6.2.2 Installing the Rectifier (TP48600B, TP481200B)

Prerequisites



The pre-fab. modules have been installed.



The rectifier delivered onsite is complete and intact after unpacking and acceptance. If
any problem is found, contact your local Huawei office.

Preparations

Tool: none

Material: rectifier

Skill requirement: skilled technician



To avoid electric shock, do not put your hands into a rectifier slot.



When a rectifier is running, a high temperature is generated around the air exhaust vent at
the rear. Do not touch the vent or cover the vent with cables or other objects.

Procedure

Step 1

Determining the position of the rectifier

Step 2

(Optional) Remove filler panels from the rectifier installation position based on the
installation requirements.

Step 3

Push the locking latch leftward and pull out the handle.

Step 4

Gently push the rectifier into its slot along the guide rails.

Step 5

Push the handle in place.

Step 6

Push the locking latch downward.

Figure 6-13

Installing the TP48600B rectifier

Summary of Contents for FusionModule1000A20












































































































Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands

Huawei FusionModule1000A20, Installation Manual

Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands