Huawei FusionModule1000A20 Installation Manual Download Page 33

Page: 33 / 107

FusionModule1000A20 Prefabricated All-in-One Data
Center
Installation Guide

4 Installing Pre-fab. Modules

Issue 02 (2020-01-15)

Context

Ensure that the crane and steel ropes can bear the load weight.

Table 4-3

Hoisting specifications

Weight

Steel
Rope
Length

Steel Rope
Quantity

Dimensions (H x W x D)

Net weight: <
6000 kg

> 6.5 m

4 PCS

2896 mm x 2438 mm x 6058 mm

Hoisting Precautions

Stage

Precautions

Before hoisting

Ensure that the crane and steel ropes provide the required bearing
capacity.

Ensure that the twistlocks in container bases are in correct positions.

Ensure that the steel ropes are securely connected.

During hoisting

Do not allow any unauthorized people to enter the hazardous areas
and never stand under the crane arm during hoisting.

Ensure that the crane is properly located and avoid long-distance
hoisting.

Keep the pre-fab. module stable and horizontal during hoisting, and
ensure that the diagonal gradient of the pre-fab. module is within 5
degrees.

Lift and land a pre-fab. module slowly to prevent shock to
equipment inside it.

Remove the ropes after ensuring that the pre-fab. module is placed
evenly on the four bases.

Preparations

Tools: crane, torque wrench, steel hoisting rope, level

Materials: pre-fab. module to be hoisted, spacer

Documents: none

Skill requirement: skilled technician, common technician, crane driver

Procedure

Step 1

Adjust the pre-fab. module in the installation direction, connect the steel hoisting ropes, and
hoist the pre-fab. module onto the bases.

Summary of Contents for FusionModule1000A20












































































































Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands

Huawei FusionModule1000A20, Installation Manual

Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands