Huawei FusionModule1000A20 Installation Manual Download

Page: 100 / 107

FusionModule1000A20 Prefabricated All-in-One Data
Center
Installation Guide

A A Basic Installation Operations

Issue 02 (2020-01-15)

Material: label

Documents: none

Skill requirement: common technician

Procedure

Step 1

(Optional) Prepare labels based on site requirements.



Label information must be clear and specific.



Labels must be easy to attach and can be securely attached.



Labels must be resistant to corrosion and deterioration.

Step 2

Select correct cable labels.

Step 3

Remove the simple labels attached to a cable during layout and attach the selected labels to
both ends of the cable.



Labels must be securely attached.



Labels must be attached in eye-catching positions on cables for ease of maintenance.



The labels on both ends of a cable must be the same.

----End

A.2 Preparing Cable Terminals

Preparations

Tools: hydraulic pliers, heat gun, and crimping tool

Materials: heat shrink tubing, DT terminal, OT terminal, and cord end terminal

Documents: none

Skill requirement: common technician

Procedure

Step 1

Figure A-15

shows how to prepare a DT terminal.

Summary of Contents for FusionModule1000A20












































































































Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands

Huawei FusionModule1000A20, Installation Manual

Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands