Huawei 7810 Administrator'S Manual Download Page 14

Page: 14 / 191

Huawei IP Phone eSpace
7810&7820&7830&7850&7870&7803X
Administrator Guide

2 Single IP Phone Configuration

Issue 01 (2011-12-31)

Huawei Proprietary and Confidential

Figure 2-2

Status tab page

Table 2-1

lists the parameters on the

Status

tab page.

Table 2-1

Parameters on the Status tab page

Parameter

Description

Firmware Version

Firmware version number, which is used to check the upgrade result.

Hardware Version

Hardware version number, which is used to identify hardware.

WAN Port Type

Method of obtaining eSpace 7850 IP address.

WAN IP Address

IP address of an IP phone.

Subnet Mask

Subnet mask of an IP phone.

MAC Address

MAC address of an IP phone, which is a hexadecimal number. MAC
addresses are important for configuring IP phones in batches.

Link Status

Connection status of the WAN port.

PC IP Address

IP address of the PC port.

Device Type

Connection type of the PC port.

DHCP Server
Status(PC)

Status of the DHCP server connecting to the LAN port.

Setting Basic Parameters for a SIP Account

eSpace 7870, 7850, 7830, 7820 and 7810 provide six lines, six lines, three lines, three lines
and two lines respectively. Each line can be configured with a SIP account.

Summary of Contents for 7810
































































































































































































Search results

Summary of Contents for 7810

Reviews:

Related manuals for 7810

Brands by name

Popular brands

Huawei 7810, Administrator'S Manual

Search results

Summary of Contents for 7810

Reviews:

Related manuals for 7810

Brands by name

Popular brands