Huawei 7810 Administrator'S Manual Download | Manualshive

Page: 136 / 191

background image

Huawei IP Phone eSpace
7810&7820&7830&7850&7870&7803X
Administrator Guide

5 Appendix

Issue 01 (2011-12-31)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

130

address for the IP phone. After the setting is complete, click

Next

repeatedly until the

setting is complete. Then the page shown in the following figure is displayed. You can
view the IP address pool information on it.

After the setting is complete, if some IP phones are set to obtain IP addresses through DHCP,
the DHCP server allocates the IP addresses in the IP address pool to the IP phones one by one.
If the lease of IP addresses is not renewed, the DHCP server withdraws the IP addresses for
use of other devices.

5.4.2 Setting Up the DHCP Server on Router AR-28

The configuration scripts and remarks for logging in to router AR-28 and enabling the DHCP
server function are as follows:

<Quidway>system-view //Enter the configuration mode.

[Quidway]dhcp enable //Enable the DHCP server function of the

router.

[Quidway]dhcp server detect //Verify the DHCP server function.

[Quidway]interface Ethernet 0/1 //Connect to network port 1 on board 0.

You must make sure that the network cable is inserted into network port 1 of board 0 on router AR-28.
In the rear panel of the router, you can view the board slots and enable DHCP function on network port
1.

[Quidway-Ethernet0/1]ip address 192.168.2.1 255.255.255.0 //Set the IP

address of network port 0/1. The router also uses the IP address as the gateway

address and allocates the IP address to the DHCP client.

[Quidway-Ethernet0/1]dhcp select interface //If the DHCP server mode

is selected based on the interface, the router can also set the DHCP server

«
...
134
135
136
137
138
...
»

Summary of Contents for 7810
































































































































































































Reviews:

No comments

Related manuals for 7810

Brand: Samsung Pages: 123

Brand: HIKVISION Pages: 2

Smartphone E-11

Brand: Etisalat Pages: 75

Brand: Alcatel Pages: 36

Brand: NTT docomo Pages: 201

Brand: Alcatel Pages: 84

Brand: Mobistel Pages: 96

Brand: Hisense Pages: 42

Brand: Nortel Pages: 52

Brand: Samsung Pages: 120

Brand: Kyocera Pages: 67

Cricket Engage LT

Brand: Zte Pages: 35

Brand: GENERAL MOBILE Pages: 56

Brand: Freeman Pages: 48

Brand: HTC Pages: 40

3360 - Cell Phone - AMPS

Brand: Nokia Pages: 178

Brand: Motorola Pages: 1

Brand: Motorola Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands