Huawei 7810 Administrator'S Manual Download Page 108

Page: 108 / 191

Huawei IP Phone eSpace
7810&7820&7830&7850&7870&7803X
Administrator Guide

4 Troubleshooting

Issue 01 (2011-12-31)

Huawei Proprietary and Confidential

102

Table 4-1

Status indicators

Indicator

Color

Status

Description

Power
supply

Green

Steady on

The power supply is connected
properly.

Blinking

The IP phone receives a call, or a
call is being muted.

Steady off

The power supply is disconnected.

Message
status
indicator

Green

Steady on

There are new messages to the IP
phone.

Steady off

There is no message to the IP
phone.

Headset
status
indicator

Green

Steady on

A headset is used.

Steady off

No headset is used.

Account
indicator

Green

Steady on

The account is occupied.

Blinking

The account receives or holds a
call.

Steady off

The phone is in the on-hook state.

Line key
assigned the
SCA
function

Green

Steady on

The listened-on account is in the
idle state.

Blinking

The listened-on account is in the
occupied state.

Steady off

The SCA function is disabled.

Line key
assigned the
BLF
function

Green

Steady on

The listened-on account is in the
idle state.

Blinking

The listened-on account is in the
occupied state.

Steady off

The BLF function is disabled.

Memory
key
assigned the
BLF
function

Green

Steady on

The listened-on account is in the
idle state.

Red

Steady on

The listened-on account is in the
talking state.

Blinking

The listened-on account is in the
ringing state.

Green/Red/Orange

Steady off

The BLF function is disabled.

Summary of Contents for 7810
































































































































































































Search results

Summary of Contents for 7810

Reviews:

Related manuals for 7810

Brands by name

Popular brands

Huawei 7810, Administrator'S Manual

Search results

Summary of Contents for 7810

Reviews:

Related manuals for 7810

Brands by name

Popular brands