HSD SM 137 D Assembly Instructions Manual Download Page 68

Page: 68 / 72

Analytical index

HSD S.p.A. © - H5834D0189IX.fm291119

setting the E-NETx address

setting the RS-485 address

installation area

environmental characteristics

installation environment maximum altitude

installation environment relative humidity

installation environment temperature

led diagnostics

lifting

overall dimensions and weight of the packed product

procedure warnings

logic power supply voltage

main parts of the servo-motor

maintenance

checking the bolts and the screws

general cleaning

safety warnings

spare parts

manufacturer

logo

manufacturer's address

manufacturer's logo

mechanical data

motor

motor shaft

moving

overall dimensions and weight of the packed product

procedure warnings

nominal power supply voltage

nominal speed

operating environment

operating temperature

orders and requests for information

overall dimensions

overall dimensions of the packed product

packing

overall dimensions and weight of the packed product

storage

preliminary information

documents supplied with the product

EC declaration of conformity

identification of the product and manufacturer

orders and requests for information

risks associated with the use of the product

scope of the manual

signs fixed to the product

symbols used in the manual

warranty

product applications

product code

product revision (product revision number)
product revision number

Rated torque

read instructions sign

reducers (see "characteristics of the reducers")
reduction (see "reduction ratio")
Reduction gear

Reduction ratio

regenerative effect on bus DC

replacing

configuration following a replacement

residual risks

risks associated with the use of the product

Prohibitions and risks associated with improper han-

dling and/or use

residual risks

RS-485

RS-485 configuration

running-in

S1 (see "technical characteristics")
S1 continuous service (see "technical characteristics")
safety

for installation and spaces

risks associated with the use of the product

safety and information signs

safety regulations

signs fixed to the product

warnings for maintenance

safety and information signs

safety regulations

screw tightening torque

serial number

service centres

servo-motor

applications

CANopen address setting

CANopen configuration

Summary of Contents for SM 137 D









































































Search results

Summary of Contents for SM 137 D

Reviews:

Related manuals for SM 137 D

Brands by name

Popular brands

HSD SM 137 D, Assembly Instructions Manual

Search results

Summary of Contents for SM 137 D

Reviews:

Related manuals for SM 137 D

Brands by name

Popular brands