background image

1    Preliminary information

HSD S.p.A. © - h0101k00a.fm291119

13

EC Declaration of Conformity

The product is built in conformity with pertinent and applicable EU Directives at the time of its 
market release, as stated in the EC declaration of conformity for which the facsimile is attached.

DICHIARAZIONE DI CONFORMITÀ UE 

(2014/30/UE ALLEGATO IV)

EU DECLARATION OF CONFORMITY 

(2014/30/EU ANNEX IV)

EU-KONFORMITÄTSERKLÄRUNG 

(2014/30/EU ANHANG IV)

DÉCLARATION UE DE CONFORMITÉ 

(2014/30/UE ANNEXE IV)

DECLARACIÓN UE DE CONFORMIDAD 

(2014/30/UE A DJUNTO   IV)

IL FABBRICANTE:

THE MANUFACTURER:

DER HERSTELLER:
LE FABRICANT:
EL FABRICANTE:

Luogo e data / Place and date / Ort und Datum / 
Lieu et date / Lugar y fecha:

Procuratore Speciale
Special Attorney
Sonderbevollmächtiger
Fondé de pouvoir extraordinaire
Mandatario Especial

Modello / Model / Modell / Modèle / Modelo:

SM 137 D

 HSD S.p.A.

MOTORE SINCRONO CON AZIONAMENTO INCORPORATO

DICHIARA SOTTO LA PROPRIA ESCLUSIVA RESPONSABILITÀ CHE IL MATERIALE ELETTRICO:

SYNCHRONOUS MOTOR WITH INCORPORATED DRIVE

DECLARES UNDER HIS OWN SOLE RESPONSIBILITY THAT THE ELECTRONIC EQUIPMENT:

SYNCHRONMOTOR MIT INTEGRIERTEM ANTRIEB

ERKLÄRT EIGENVERANTWORTLICH, DASS DAS ELEKTROMATERIAL:

MOTEUR SYNCHRONE À ACTIONNEMENT INCORPORÉ

DÉCLARE SOUS SA SEULE RESPONSABILITÉ QUE LE MATÉRIEL ÉLECTRIQUE:

MOTOR SÍNCRONO CON ACCIONAMIENTO INCORPORADO

DECLARA BAJO SU EXCLUSIVA RESPONSABILIDAD QUE EL MATERIAL ELÉCTRICO:

Denominazione commerciale / Commercial name / 
Handelsbezeichnung / Nom commercial / Denominación comercial

IT

EN

DE

FR

ES

registered office:

 Via Della Meccanica, 16 - 61122 Pesaro (PU) Italy

factory headquarters:

 Via Pesaro, 10A - 61012 Gradara (PU) Italy

Tel.: (+39) 0541 979 001 - Fax: (+39) 0541 979 050

E

 CHE SONO STATE APPLICATE LE PARTI PERTINENTI DELLE SEGUENTI NORME ARMONIZZATE: 

EN 60034-1:2010+AC:2010

, EN 61800-3:2004+A1:2012.

È

 CONFORME ALLA PERTINENTE NORMATIVA DI ARMONIZZAZIONE DELL’UNIONE:

x

2014/30/UE

DEL PARLAMENTO EUROPEO E DEL CONSIGLIO del 26 febbraio 2014, concernente l’armonizzazione delle legislazioni 
degli Stati membri relative alla compatibilità elettromagnetica

A

ND THAT THE RELEVANT PARTS OF THE FOLLOWING HARMONISED STANDARDS HAVE BEEN APPLIED: 

EN 60034-1:2010+AC:2010

, EN 61800-3:2004+A1:2012.

I

S IN CONFORMITY WITH THE RELEVANT UNION HARMONISATION LEGISLATION:

x

2014/30/EU

OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 26 February 2014, on the harmonisation of the laws of the 
Member States relating to electromagnetic compatibility

U

ND DASS DIE EINSCHLÄGIGEN TEILE FOLGENDE HARMONISIERTEN NORMEN ANGEWANDT WURDEN: 

EN 60034-1:2010+AC:2010

, EN 61800-3:2004+A1:2012.

D

IE EINSCHLÄGIGEN HARMONISIERUNGSRECHTSVORSCHRIFTEN DER UNION ERFÜLLT:

x

2014/30/EU

DES EUROPÄISCHEN PARLAMENTS UND DES RATES vom 26. Februar 2014, zur Harmonisierung der 
Rechtsvorschriften der Mitgliedstaaten über die elektromagnetische Verträglichkeit

E

T QUE LES PARTIES PERTINENTES DES NORMES HARMONISÉES SUIVANTES ONT ÉTÉ APPLIQUÉES: 

EN 60034-1:2010+AC:2010

, EN 61800-3:2004+A1:2012.

E

ST CONFORME À LA LÉGISLATION D’HARMONISATION DE L’UNION APPLICABLE:

x

2014/30/UE

DU PARLEMENT EUROPÉEN ET DU CONSEIL du 26 février 2014, relative à l’harmonisation des législations des États 
membres concernant la compatibilité électromagnétique

Y

 QUE HAN SIDO APLICADAS LAS PARTES PERTINENTES DE LAS SIGUIENTES NORMAS ARMONIZADAS: 

EN 60034-1:2010+AC:2010

, EN 61800-3:2004+A1:2012.

E

S CONFORME CON LA LEGISLACIÓN DE ARMONIZACIÓN PERTINENTE DE LA UNIÓN:

x

2014/30/UE

DEL PARLAMENTO EUROPEO Y DEL CONSEJO de 26 de febrero de 2014, sobre la armonización de las legislaciones de 
los Estados miembros en materia de compatibilidad electromagnética

)$&6,0,/(

Summary of Contents for SM 137 D









































































Reviews: