HSD SM 137 D Assembly Instructions Manual Download Page 57

Page: 57 / 72

A Technical characteristics

HSD S.p.A. © - h0124k00a.fm291119

FIELDBUS INTERFACES

Enet-X / CANopen / RS-485

See paragraph

5.6 “Fieldbus interfaces”

OPERATING ENVIRONMENT

unit

Value

Workplace temperature

°C (°F)

5 to 40 (41 to 104)

Storage temperature

°C (°F)

-25 to 55 (-13 to

131)

Transport temperature

°C (°F)

-25 to 70 (-13 to

158)

Relative workplace humidity (non-condensed)
@ 5 to 40°C (41 to 104°F)

5-85

Relative storage humidity (non-condensed)
@ -25 to 55°C (-13 to 131°F)

5-95

Relative transport humidity (non-condensed) @ 40°C (104°F)

Maximum workplace altitude (unless otherwise agreed)

A.S.L.

2000

(6500ft)

Storage maximum workplace altitude

EMC immunity area (CEI EN 61800-3)

Second

environment

Summary of Contents for SM 137 D









































































Search results

Summary of Contents for SM 137 D

Reviews:

Related manuals for SM 137 D

Brands by name

Popular brands

HSD SM 137 D, Assembly Instructions Manual

Search results

Summary of Contents for SM 137 D

Reviews:

Related manuals for SM 137 D

Brands by name

Popular brands