HSD SM 137 D Assembly Instructions Manual Download Page 25

Page: 25 / 72

3 Main parts

HSD S.p.A. © - h0102k00a.fm291119

3.3

Identification of the manufacturer and the

product

The name and address of the manufacturer are:

HSD S.p.A.

main headquarters:

Via Pesaro, 10A - 61012 Gradara (PU) ITALY

registered offices:

Via della Meccanica, 16 - 61122 Pesaro ITALY

The manufacturer and the product are identified on the plate fixed to the motor body. The plate
contains the information listed below.

- manufacturer's logo and

address; product name

- rated power supply voltage

- logic supply voltage

- nominal speed

- nominal torque

- danger sign - hot surfaces

- sign - obligation to read

instructions

- EC mark

serial number

- product code and revision

number (GDT)

- firmware code and revision

number (GDT)

3.4

Safety and information signs

For the safety and information signs, refer to paragraph

2.5 “Signs fixed to the product”

Summary of Contents for SM 137 D









































































Search results

Summary of Contents for SM 137 D

Reviews:

Related manuals for SM 137 D

Brands by name

Popular brands

HSD SM 137 D, Assembly Instructions Manual

Search results

Summary of Contents for SM 137 D

Reviews:

Related manuals for SM 137 D

Brands by name

Popular brands