HS Tarm 2000 Installation And Operation Manual Download Page 18

Page: 18 / 66

NSTALLATION (continued)

PAGE 14

__________________________________________________________________________________________________________________________________________________________________________________

BOILER PACKING LIST

NOTE:

PLEASE CHECK OFF THE FOLLOWING ITEMS ON THE LISTS BELOW:

•

A complete Excel 2000 series boiler, as shipped from our warehouse, consists of five (5)

pieces, as follows:

BOILER BODY

Ash Removal Pan

Ash Removal/Scraper Tool

Cleaning Brush

Installation Manual & Warranty Package

Box Containing Draft Fan

Flue

Outlet

Turbulators – 6/EXCEL 2000, 8/EXCEL 2200 – should be installed in oil/gas heat exchange tubes

JACKET BOX

One (1) Front Panel

Four (4) Side Panels (2 left & 2 right)

One (1) Rear Panel

Two (2) Top Panels (front & rear)

Six (6) Pieces Steel Zip Strips

DOOR BOX

Door

Ash Door (with viewing port)

By-Pass Lever Bakelite Knob (larger)

Secondary Air Bakelite Knob (smaller)

Plastic Bag Containing Eight (8) Door Mounting Bolts

Bakelite Handles for Doors (2)

One (1) Can of Door Mounting Cement and Applicator (Stovex)

SAFETY CONTROL PACKAGE

Boiler Pressure Relief Valve (#10-102-05, 30 psi)

Boiler Control Panel with Pre-Wired Honeywell Controls

Draft Fan Low Temp Cut-Off Control

Two (2) Pieces Immersion Well, 3/4 inch

Pressure/Temperature

Gauge

Coil Pressure Relief Valve (#17-402-02, 100psi)(optional)

BURNER BOX

Oil Burner For EXCEL 2000 includes I GPH nozzle – For EXCEL 2200 includes 1.25 GPH nozzle

and F-6 Retention Head.

Gas Burner Includes a duel acting Draft Regulator and a Manual Re-set spill switch.

•

Please contact your dealer immediately if any of the above items are missing!

•

TARM USA, INC. reserves the right to substitute equivalent equipment for any of the

controls and accessories specified above.

Summary of Contents for 2000



































































Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands

HS Tarm 2000, Installation And Operation Manual

Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands