manualshive.com logo in svg

HS Tarm 2000, Installation And Operation Manual

Share
Download
HS Tarm 2000 Installation And Operation Manual Download Page 38

 

I

NSTALLATION  (continued)

                                                                                                                                                  PAGE 33

 

______________________________________________________________________________________________________________________________________________________________________________________ 

 
PIPING TO HEAT DISTRIBUTION IN HOME (continued)

 

 

   

Radiant Floor Heating

 

 

 

An increasing number of HS-Tarm boilers are being installed with radiant floor heating systems.  
Your heating system installer and/or your radiant floor equipment supplier will supply needed 
design and installation details.

 

 

   

Hot Air Heating

 

 

 

Boilers can be used in a number of ways to provide hot air heating.  This can be done with 
existing forced hot air heating systems and in new construction.  Again, your system installer 
and/or your equipment supplier should supply the needed design and installation details.

 

 

FILLING YOUR BOILER

 

 

 

Fill your Tarm EXCEL boiler and heating system in the conventional manner.  

 

 

 NOTE: 

 

The boiler may be protected with antifreeze.  It should be propylene glycol and 

should be checked annually for proper freeze protection and P.H. level.  
HOWEVER, please remember that the domestic hot water coil, if you have one, is 
not protected by the antifreeze. Also, please be aware that the use of antifreeze in 
your system may decrease heat exchange efficiency 5-10%. 

 
 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

33 

Summary of Contents for 2000



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands