HS Tarm 2000 Installation And Operation Manual Download Page 3

Page: 3 / 66

ADDENDUM

Before starting your boiler installation, we urge you to read and consider this

addendum.

Tarm Biomass strongly recommends the installation of a Termovar automatic, thermally

operated, 3-way mixing valve or loading unit with all wood or multi-fuel boilers.

When cold water returns to the boiler it causes sweating and a cold environment for

the fire which causes creosote and poor combustion.

The Termovar insures a minimum return water temperature of 160

F in the boiler.

This increases efficiency, helps prevent creosote, and considerably extends the life of the
boiler.

The Termovar helps create more efficient burning and is a recommended part of any boiler

installation.

Please call Tarm Biomass with any questions.

1-800-782-9927

IMPORTANT NOTICE:

Any tubing used for Radiant Floor Heating with a Tarm Biomass

boiler MUST have an oxygen barrier.

Summary of Contents for 2000



































































Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands

HS Tarm 2000, Installation And Operation Manual

Search results

Summary of Contents for 2000

Reviews:

Related manuals for 2000

Brands by name

Popular brands