I
NTRODUCTION
A
ND
I
MPORTANT
I
NFORMATION (continued)
PAGE 5
______________________________________________________________________________________________________________________________________________________________________________________
PLEASE READ THIS PAGE CAREFULLY!
This boiler has a limited warranty which is included with
your boiler as a separate enclosure. To validate your
warranty, detach the postcard, fill in all information
requested, and return the card to TARM USA, INC.
Please always raise questions or warranty claims with
your installer/dealer who delivered the boiler to you.
The installer/dealer then passes the claim on to TARM
USA, INC., IF NEED BE. However, claims may also be
raised directly with TARM USA, INC.
General Information
Please read the literature enclosed by the
manufacturers regarding the various accessory devices.
These devices are warranted by the manufacturer, NOT
by TARM USA, INC. These accessory devices must be
installed and used according to the recommendations of
the manufacturer unless instructed otherwise in this
manual.
NOTE: All boilers must be installed in accordance with
national, state and local plumbing, heating and electrical
codes, and the regulations of the serving electric, water
and gas utilities.
Plumbing diagrams in this manual are for basic
information only and may not show all valves, vents,
fittings, etc that are normally included in finished boiler
installations.
All systems should be designed by competent
contractors, and only persons knowledgeable in the
layout and installation of heating systems should
attempt the installation of any boiler.
It is the responsibility of the installing contractor to see
that all controls are installed correctly and that they are
operating properly when the installation is complete.
If any fans are used in the fuel storage area, they should
be installed so as not to create negative pressure in the
room where the solid-fueled burning appliance is
located.
Please read carefully the section “OPERATION
DURING SUMMER”. Failure to protect your boiler from
condensation during the warmer months MAY VOID
YOUR WARRANTY! SEE PAGE 48.
Do not use this boiler if any part has been under water.
Immediately call a qualified service technician to inspect
the boiler and to replace any part of the control system
and any gas control which has been under water.
Homeowners should read and familiarize themselves
with “BOILER OVERHEATING” and “OPERATING IN
THE EVENT OF POWER FAILURE”. SEE PAGES 53
TO 55.
WARNING: Do not use gasoline, kerosene or other
flammable liquids to start or maintain solid-fuel fires in
your boiler. Serious burns and property damage may
result.
WARNING: Do not store any combustibles, including
fuel for the boiler, within the fire clearances specified
below in “Installation Information”. Keep fuel clear of the
fuel-loading and ash-removal access areas.
WARNING: This boiler is designed to burn wood. Both
hard and soft woods may be used, but under no
circumstances should you burn coal or small pieces of
wood or wood waste that can fall through the center slot
in the refractory causing a blockage.
Installation Information
The boiler must be connected to a tile-lined masonry flue
or other Type HT approved chimney. No other appliance
should be connected to this flue. Consult your local
building inspector for chimney requirements, and install
the boiler in accordance with all applicable codes.
The boiler requires adequate fresh air supply for efficient
and safe operation. For more information refer to NFPA
Standard #31 and page 6.
The boiler must be positioned to provide minimum
clearances from combustibles or combustible surfaces
as follows: LEFT SIDE=24”; RIGHT SIDE=12”; TOP
AND REAR=18”; FRONT=36”.
There must be a minimum clearance of 18” between
smoke pipe and all combustible surfaces.
Use the wicking and pipe dope supplied with the boiler to
seal all threaded connections to the boiler and Termovar.
When references are made to tapping numbers, please
refer to Page 9.
Do not use self-contained, non-electric zone valves on
the main heating zone as it is to be used as the
overheat/dump zone.
Do not use any radiant floor tubing that does not
have an oxygen barrier with any EXCEL Boiler.
Installation must conform to ANSI/NFPA standard #211
MINIMUM REQUIRED FLUE SIZE – 8”X 8” TILE OR 6” ROUND
MINIMUM DRAFT -- .05 IN/WG DURING NORMAL OPERATION
5
Summary of Contents for 2000
