HP XT905UT User Manual Download Page 161

Page: 161 / 183

Select

To do this

Built-In Device Options

●

Enable/disable the wireless button state (enabled by
default).

●

Enable/disable embedded WLAN device radio (select
models only; enabled by default).

●

Enable/disable the embedded Bluetooth device radio
(enabled by default).

●

Enable/disable the Network Interface Controller (LAN)
(enabled by default).

●

Enable/disable LAN/WLAN switching (disabled by
default).

●

Set the wake on LAN state. Options include the
following:

◦

Disabled

◦

Boot to Network

◦

Follow Boot Order

●

Enable/disable the Ambient Light Sensor.

●

Enable/disable the Notebook Upgrade Bay device
(enabled by default).

●

Enable/disable the fingerprint device (enabled by
default).

●

Enable/disable the integrated camera (enabled by
default).

●

Enable/disable the Power Monitor Circuit (enabled by
default).

●

Enable/disable the audio device (enabled by default).

●

Enable/disable a modem device (enabled by default).

●

Enable/disable the microphone (enabled by default).

●

Enable/disable the internal speakers (enabled by
default).

Computer Setup menus 149

Summary of Contents for XT905UT
























































































































































































Search results

Summary of Contents for XT905UT

Reviews:

HP XT905UT, User Manual, Page: 161 / 183

Search results

Summary of Contents for XT905UT

Reviews: