HP XT905UT User Manual Download Page 109

Page: 109 / 183

CAUTION:

To prevent damage to a USB connector, do not pull on the cable to remove the USB device.

To stop and remove a USB device:

Double-click the

Safely Remove Hardware

icon in the notification area, at the far right of the

taskbar.

NOTE:

To display the Safely Remove Hardware icon, click the

Show Hidden Icons

icon (

) in the notification area.

Click the name of the device in the list.

NOTE:

If the USB device is not listed, you do not have to stop the device before you remove it.

Click

Stop

, and then click

Remove the device.

Using USB legacy support

USB legacy support (enabled at the factory) permits the following actions:

●

Using a USB keyboard, mouse, or hub connected to a USB port on the computer during startup or
in an MS-DOS-based program or utility

●

Starting or restarting from an optional external MultiBay or an optional USB bootable device

To disable or reenable USB legacy support in Computer Setup, follow these steps:

Turn on or restart the computer, and then press

esc

while the “Press the ESC key for Startup Menu”

message is displayed at the bottom of the screen.

Press

f10

to enter the BIOS Setup.

Use a pointing device or the arrow keys to select

System Configuration

, and then select

Device

Configurations

To disable USB legacy support, click

Disabled

next to

USB legacy support

. To reenable USB

legacy support, click

Enabled

next to

USB legacy support

To save your changes and exit Computer Setup, click

Save

in the lower-left corner of the screen,

and then follow the on-screen instructions.

– or –

Use the arrow keys to select

File

Save changes and exit

, and then follow the on-screen

instructions.

Your changes go into effect when the computer restarts.

Using a USB device

Summary of Contents for XT905UT
























































































































































































Search results

Summary of Contents for XT905UT

Reviews:

HP XT905UT, User Manual, Page: 109 / 183

Search results

Summary of Contents for XT905UT

Reviews: