manualshive.com logo in svg

HP XT905UT, User Manual, Page: 111 / 183

Share
Download
HP XT905UT User Manual Download Page 111

Using an eSATA device

An eSATA port connects an optional high-performance eSATA component, such as an eSATA external
hard drive.

Some eSATA devices may require additional support software, which is usually included with the device.
For more information about device-specific software, refer to the software manufacturer’s instructions.
These instructions may be provided with the software, on disc, or on the manufacturer’s Web site.

Connecting an eSATA device

CAUTION:

To prevent damage to an eSATA port connector, use minimal force to connect an eSATA

device.

▲

To connect an eSATA device to the computer, connect the eSATA cable for the device to the
eSATA port.

You will hear a sound when the device has been detected.

Stopping and removing an eSATA device

CAUTION:

To prevent loss of information or an unresponsive system, stop the eSATA device before

removing it.

CAUTION:

To prevent damage to an eSATA connector, do not pull on the cable to remove the eSATA

device.

1.

Double-click the 

Safely Remove Hardware

 icon in the notification area, at the far right of the

taskbar.

NOTE:

To display the Safely Remove Hardware icon, click the 

Show Hidden Icons

 icon

(

<

 or 

<<

) in the notification area.

2.

Click the name of the device in the list.

NOTE:

If the device is not displayed, you do not have to stop the device before you remove it.

3.

Click 

Stop

, and then click 

OK

.

4.

Remove the device.

Using an eSATA device

99

Summary of Contents for XT905UT
























































































































































































Reviews:

No comments