Honeywell X-618 Commissioning Manual Download Page 9

Page: 9 / 57

3 Basic Operations

This chapter describes the basic operations of the X-618 Config software.

Running the Software

Note:

Make sure X-SMART software and the X-618 Config software are not running at the same time.

If the X-SMART software is running, the X-618 Contig software cannot be run.

The steps for running the software are as follows:

1. Click

Start

at the lower left of your computer desktop, and select

Program



X-618 Config



X-

618 Config

2. Select the menu commands Tools



Select Language, the Select Language window is

displayed. The user can select the appropriate language. Click OK. The main window which is
shown in English is displayed as shown in Figure 3.

Figure 3 X-618 Config Software Initial Window

Exiting the Software

Select the menu commands

Project



Exit or click the

“X” icon

on the upper right corner

, a prompt

dialogue displays. Click

Yes

in this prompt dialogue to exit the software.

Summary of Contents for X-618


























































Search results

Summary of Contents for X-618

Reviews:

Related manuals for X-618

Brands by name

Popular brands

Honeywell X-618, Commissioning Manual

Search results

Summary of Contents for X-618

Reviews:

Related manuals for X-618

Brands by name

Popular brands