Honeywell X-618 Commissioning Manual Download Page 7 | Manualshive

Page: 7 / 57

background image

6

2 Software Installation

This chapter describes the runtime environment and installation and uninstallation procedures of
the X-618 Config software.

Run Environment

The X-618 Config software sends configuration data to devices within the system through the
network. The computer on which the software is installed must meet the following requirements:



Windows 7, Windows 8 and Windows 10 operating system

(The software is untested in other Windows operating systems.)



1GHz or higher CPU



At least 512MB RAM



At least 1GB of available disk space



10M/100M Ethernet interface



Running at 1024X768 resolution or higher



The software should be granted network access by firewall.

Software Installation

The X-618 Config software is easy to install by following an installation wizard.

1. Put the X-618 system CD into the CD-ROM drive, click X-618 System Commissioning Tool in

the Autorun view or double-click the installation program X-618 Config.exe, and the X-618
Config installation wizard window displays as shown in Figure 1.

Figure 1 X-618 Config Installation Wizard Page

2. Click

Next

. The

License Agreement page is displayed.

3. Select

I Agree

on the page.

4. Click

Next

. The information page is displayed.

Read the important information on this page before proceeding to the next step.

«
...
5
6
7
8
9
...
»

Summary of Contents for X-618


























































Reviews:

No comments

Related manuals for X-618

Brand: Omega Engineering Pages: 2

Brand: Randall Pages: 12

Brand: Kathrein Pages: 8

Brand: Kathrein Pages: 8

EVO PHONODAC TWO

Brand: M2TECH Pages: 2

Brand: Yamaha Pages: 2

Brand: Yamaha Pages: 35

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 8

Brand: Perreaux Pages: 2

Brand: HR Pages: 12

Brand: Peavey Pages: 44

Brand: Simaudio Pages: 11

Two-Rock Jet Signature

Brand: K&M Analog Designs Pages: 7

Brand: Plinius Pages: 22

Brand: Nobsound Pages: 2

Subamp SBA-12000

Brand: Lynx Pages: 12

Brand: icon Audio Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands