Honeywell HomMed Genesis Programming And Troubleshooting Manual Download Page 22

Page: 22 / 26

GENESIS

DM MONITOR

Programming/Troubleshooting Guide

P4520EN.04 07/14/2010

VFD Display

Meaning

Possible Cause

Resolution/Action

324 PAGER_MSG_FAIL

Message

failed

If problem persists, call
Honeywell HomMed.

350 GPRS

Requires

Reset

Modem responded with an error
the monitor doesn't handle, too

early to be more specific with
causes here

If problem persists, call
Honeywell HomMed

351

Call Customer Service

Improper Hardware Setup

SIM card is missing or not
enabled

If problem persists, call
Honeywell HomMed

352

GPRS Service Unavailable

Signal is too weak for the
modem to work

No service in the area

If problem persists, call
Honeywell HomMed.

353

GPRS Network Fail

Access Point Name is not
configured correctly on the

modem

No service in the area

If problem persists, call
Honeywell HomMed.

410 GLUCO_TIMEOUT

User timeout – glucose
meter

Patient noncompliance

Retrain the patient.

411

GLUCO_COMM

Glucose meter disconnected

Glucose meter cable not

connected

Loose Connection

Connect the cable.

Make sure all connections are
secure.

412

GLUCO_OFF

Glucose meter not enabled

In Options menu, set appropriate

glucose meter to On.

413 WRONG_GLUCO

ID Card and monitor setup
gluco-type mismatch

Program the card or the monitor
for the correct glucose meter.

420

SPIRO_TIMEOUT

User timeout - spirometer

Patient noncompliance

Retrain the patient.

421 SPIRO_COMM

Spirometer

disconnected

Spirometer cable not connected

Loose connection

Connect the cable.

Make sure all connections are
secure.

422 SPIRO_OFF

Spirometer not enabled (no

assigned COM port)

In Options menu, set appropriate

spirometer to On.

430

PT_TIMEOUT

User timeout – PT/INR

Patient noncompliance

Retrain the patient.

431 PT_COMM

PT/INR

disconnected

PT/INR cable not connected

Loose connection

Connect the cable.

Make sure all connections are
secure.

432 PT_OFF

PT/INR not enabled (no
assigned COM port)

In Options menu, set appropriate
PT/INR to On.

440

ERROR_ECG_TIMEOUT

User timeout – ECG

Patient noncompliance

Retrain patient.

441 ERROR_ECG_COMM

ECG

disconnected

ECG cable not connected

Loose connection

Connect cable.

Make sure all connections are
secure.

442 ERROR_ECG_OFF

ECG not assigned a COM

port

In Options menu, set ECG to On.

450

PEAKFLOW_TIMEOUT

User timeout – peak flow

Patient noncompliance

Retrain the patient.

Summary of Contents for HomMed Genesis



























Search results

Summary of Contents for HomMed Genesis

Reviews:

Related manuals for HomMed Genesis

Brands by name

Popular brands

Honeywell HomMed Genesis, Programming And Troubleshooting Manual

Search results

Summary of Contents for HomMed Genesis

Reviews:

Related manuals for HomMed Genesis

Brands by name

Popular brands