Honeywell HomMed Genesis Programming And Troubleshooting Manual Download Page 25

Page: 25 / 26

GENESIS

DM MONITOR

Programming/Troubleshooting Guide

P4520EN.04 07/14/2010

VFD Display

Meaning

Possible Cause

Resolution/Action

617

MODEM NOT READY

Modem was not ready.

If problem persists, call
Honeywell HomMed.

901

RAM_ERROR

RAM self test failed

Call Honeywell HomMed.

902

ROM_ERROR

ROM Checksum error

Call Honeywell HomMed.

903

UART_ERROR

Hardware error

Call Honeywell HomMed.

904

RTCC_ERROR

Real time clock failure

Call Honeywell HomMed.

910 ERROR_FILE_SYSTEM

Language text files missing
or corrupt

Replace the SmartMedia card.

911

DISK_ERROR

SmartMedia failure

Replace the SmartMedia card.

912 DISK_ERROR_BAD_FORMAT SmartMedia failure – bad

format

Replace the SmartMedia card.

913 DISK_ERROR_NO_CARD

SmartMedia failure – card
removed

Insert the correct SmartMedia
card.

914 DISK_ERROR_BAD_CARD

SmartMedia failure – bad

card

Replace the SmartMedia card.

915 DISK_ERROR_CHANGED_CARD SmartMedia failure – card

swapped

Reboot the unit; if problem
persists, call Honeywell HomMed.

916 DISK_ERROR_CARD_FAILURE SmartMedia failure – card

failure

Replace SmartMedia card; if

problem persists, call Honeywell
HomMed.

930 PHOTOCARD

TIMEOUT

No response – card
removed or defective

Card removed before monitor
could download images.

Defective card

Retrain the patient.

Use new card, retake photo,

resend.

931 PHOTOCARD

FAILURE

Card not readable:
damaged, wrong type

Use only SmartMedia cards for
digital images.

Use new card, retake photo,

resend.

932 PHOTOCARD

READ

ERROR

Invalid CRC, parity error,
etc.

Take another picture and resend.

Use new card, retake photo,

resend.

933

PHOTOCARD CONFIG BAD

Config. file (*.CFG) missing
or contains invalid info

Use only appropriate SmartMedia
cards for digital images.

Use new card, retake photo, and

resend.

934

PHOTOCARD PAT. ID BAD

Pt. ID file (*.PAT) missing or
contains invalid info

Use new card, retake photo, and
resend.

935

PHOTO NOT FOUND

No photos in photo

Summary of Contents for HomMed Genesis



























Search results

Summary of Contents for HomMed Genesis

Reviews:

Related manuals for HomMed Genesis

Brands by name

Popular brands

Honeywell HomMed Genesis, Programming And Troubleshooting Manual

Search results

Summary of Contents for HomMed Genesis

Reviews:

Related manuals for HomMed Genesis

Brands by name

Popular brands